On my 1984 Toyota 4x4 it was on the passenger side on the frame rail next to the fuel tank about 4 inches from the filler hose this is not an easy place to get to but if you can relocate it in the engine bay for future replacement as with older rigs you get more sediment in the tank witch equals to changing the filter more often. If so, we're going to show you how to relocate your tank on a body-lifted Toyota to gain clearance under and preserve capacity in the tank: In this case, our project vehicle is a 2nd-generation 4Runner used for rockcrawling in the desert southwest. Answer: Toyotas have the same fuel tank design as all the other vehicles out there, making it a matter of simple physics to siphon gasoline out with a hose. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge excludes shipping charges for the original purchaser. The firing order of any engine should be cast into the intake manifold.
Lowest price on brand new, in-the-box auto parts. We grew tired of dragging the gas tank on our 4Runner, so we sought a good solution to the problem while still retaining the stock components. I know that the carb and efi vent and returns are done the same way at least for what I was looking at last night. Smell of fuel inside the cabin The potent smell of fuel inside your pickup may also be due to a leak from a corroded or punctured fuel tank. It's not entirely resistant to damage; in fact, fuel tank problems are one of the most common issues that Toyota Pickup owners are likely to encounter.
It's also sold individually and features a natural finish. Always keep in mind that even the smallest amount of water is damaging to your fuel tank. At that time, however, my fuel gauge still worked. I had to replace the hanger and the pump at the same time. The venting system in your vehicle can also malfunction and make it hard for you to put gas in the tank.
We know you love your Toyota Pickup and want to make sure it's taken care of maybe he or she even has a name? The brackets were then welded to the frame, and finally the tank was bolted in. We decided to use hose and not continue the hardline that the factory setup has, because we felt that high-pressure gas hose was plenty strong. This is one of the most notorious causes of fuel tank problems. It's quite a long wait, but this is a step you must not skip. Finally, we removed the gas tank, and allowed the tank to air out.
The relocation purpose is two-fold: It allows the tank to be considerably higher off the ground, and puts it in a location much less prone to rock damage. Its multi-layered construction withstands corrosion-inducing circumstances such as saltwater or moisture. At cruising speed the vacuum switching valve opens and the stored vapors are drawn into the intake manifold along with fresh air drawn through the air filter. Just go ahead and call the phone number at the top of the page and a friendly specialist will help you out. I haven't had time to drop mine yet, plus I simply don't have any extra money to put into this project right now.
Then crack open the high pressure side where it attaches to the hard line at the frame. If you put fuel back in a tank, which hasn't yet completely dried off, it will just mix with excess water. For this project, there are 5 hoses and 4 wires that need to be extended. The first picture shows the tank in the new location, prior to wrapping up the install. Make sure that the cleaning solution you'll be using is compatible with the type of engine that you have. I think the vent is the line that is towards the front of the truck, and the return is the line towards the back.
The first is to drive the Pickup around until the fuel is consumed-a fun option, no doubt, but it can be time consuming. However, if there is more water than the additive can handle, your only solution is to replace all the fuel inside the tank. Check the manifold for a series of numbers that agrees with the number of cylinders in your engine. Although not very prone to failure, fuel tank problems can still arise from time to time. I hate dropping gas tanks. Don't forget to catch all that expensive liquid in a container for reuse or proper disposal. Always remember that fuel leaks are very dangerous and should be fixed as soon as possible to prevent fire or explosion.
A good way to verify water and microbial contamination in your Toyota Pickup fuel tank is by using commercial testing kits. This item can only be shipped to a physical address within the 48 contiguous U. The standard 1985 Toyota pickup truck was 185 inches in length, and had a wheelbase of 102. If you decide to do this tak … e your time, strip the carburated engine down to the block and head then slowly and making sure you label where everything goes put the fuel injection parts on. This will usually take you about 24 to 48 hours.
You may also experience sputtering. Towing capacity was 3,500 pounds. Some tanks can be made out of steel or aluminum and welded from stamped sheets. We here at Auto Parts Warehouse want to make sure you're happy with your car part purchases. Check engine light turns on and leak is detected Another problem that you might encounter with your Toyota fuel tank is evaporative leak. Been laid off twice this summer, I'm back in school and I don't start my part time job til next week, or possibly the next week.