Pop the hood, and disconnect the negative battery terminal. I tightened the bolts in a cross pattern top left, bottom right, top right, bottom left to pull the bearing assembly as straight as possible into the bore. It can still help to warm it up. It can still help to warm it up. Make sure you use new hub-bearing bolts because these are single use bolts and if they fail your wheel will fall off. Then, once car is on ground, +180 degree turn.
As a preventive strategy, it is wise to regularly monitor your car or truck in regular basis between drives. I have 76K miles on my original bearing. The hub bearing assembly is designed to support the vehicle's weight and reduce resistance so that your wheels maintain contact with the road under any condition. Good luck adding that ½ turn, I could barely move the bolt at all after it was torqued to spec. Brother in law had a nice long 6ft rachet to aid in the removal and tightening of the 18mm Triple Square Bolt.
Advance said they would replace it with a Moog hub assembly plus extra cost. Bolt the steering knuckle onto the wheel hub in the same orientation it was before you removed it. I was about to buy new rear wheel bearing thinking the A4 body style was still like the A2's, cheap and easy, no pullers required. Remove the axle nut at the center of the wheel with an adjustable wrench. . The resulting system stiffness reduces rotor run-out and improves brake performance.
These magnetic poles must always lie opposite the wheel sensor. Don't remove the wheel bolts until the car is safely lifted and secured on jack stands. We're here to help you find that perfect Wheel Bearing for your Volkswagen Jetta. This is a major advantage so you do not have to worry about grease or seal application. Here is where the jack stand points were on my car:. Pull out the old snap ring, and use the press tool to remove the bearing from the knuckle. Tighten to 129 ft lbs.
A few minor corrections on the brake disassembly. If you're changing both sides not needed unless they're both bad before raising the car to keep the car stable. Reconnect the negative battery terminal. Maybe I'm just being paranoid, but this all is so fishy to me. Several months ago, the brake booster needed to be replaced. I changed a bearing at ~50k because I thought it was bad. .
Sensor's speed information can be used for vehicle dynamics control systems, speed control, speedometer, odometer, trip computer and other purposes. It is a 24mm triple square socket. I Used A Hammer To Hit The Hub And Remove The Bearing Assembly Shattered Assembly There is a hole on the back side of the steering knuckle that allows a punch to be inserted. Remove the brake caliper and rotor. The below Amazon link is what i used to get the. Notes: Wheel Bearing and Hub Assembly -- With Torsion Beam Suspension.
Unbolt the brake caliper, which grips the wheel hub, from the front wheel, and immediately hang it from a wire coat hanger hooked to the suspension or the frame of the car. Anyone have torque values on the bolts for re-intallation? He said it was extremely unlikely and that if it were, my brakes probably wouldn't have popped back on. Suspend the caliper from the wire. Thanks I was about to buy new rear wheel bearing thinking the A4 body style was still like the A2's, cheap and easy, no pullers required. Place the brake calipers on the wheel hub, and tighten them with a torque wrench according to the recommended foot-pound specifications. Use the same three jaw puller to remove the inner race of the bearing from the stub axle.
This vehicle has push button start, which means the brake pedal must be depressed before attempting to start the vehicle. Any Tricks on finding out if it is front or back???? I believe that one of them is out of round or that something is wrong with one. Shop online, find the best price on the right product, and have it shipped right to your door. This worked on one side and the wheel bearing assembly came out without too much of an issue. Ensure Proper FitTo confirm that this part fits your vehicle, enter your vehicle's Year, Make, Model, Trim and Engine in the Compatibility Table. Replace your worn or warped wheel bearings with these premium quality and durable products that we offer.
My tires don't create that much noise and with 110,000 miles approaching this seems logical. When depressing the brake pedal, the pedal felt hard. Put the wheel back on the bolts, and use the torque wrench to tighten the nuts holding it on. I have a wheel bearing going bad but I can not tell if the noise is coming from front or back. Post Mortem: · Compared to the front, the rear is a piece of cake.